BACK PLATE & HARNESS

TDS stainless steel back plate for technical diving with a matte polished finish, 3 mm thick and weighing 2.1 kg.

TDS stainless steel backplate for technical diving with a matte polished finish, 3 mm thick and weighing 2.1 kg.

TDS Anodized Aluminum Reduced Back Plate. Ideal for travel thanks to its light weight: only 500 g. Perimeter edges and perforations completely beveled to avoid damaging equipment and harness straps.

Plate for mounting a single bottle on back plate, in stailess steel. Includes set of two bottle straps with stainless steel buckle. Also includes a complete set of screws with spherical head, square body to avoid turning when tightening, washers and wing nuts. Approximate weight of the set 1 kg

TDS DIR Harness Scuba Diving Harnais: Technical harness for mounting on back plate (not included), with all necessary components included for a basic DIR configuration. The set is sold disassembled for the diver to assemble on his plate with his personal settings and preferences.

TDS Confort Plus Techncial Scuba Diving Harnais: Technical harness for mounting on back plate (not included) with adjustable and removable shoulder straps and all additional components. The set is sold disassembled so that the diver can mount it on his plate adapting it to his measurements and configuration preferences.

Technical harness for mounting on back plate (not included) with adjustable shoulder straps (not removable), and all additional components. The set is sold disassembled so that the diver can mount it on his plate adapting it to his measurements and configuration preferences.

The TDS Tolok pocket, is a specially pocket designed for technical diving, being valid for both backmount and sidemount systems thanks to the versatility of its design. A pocket designed down to the smallest detail to offer maximum performance to the technical diver.

Ballast system for back plate, consisting of two pockets that are attached to a webbing and end in a riveted ring, which is attached to the holes of the back plate. The left pocket includes a D-ring for attaching a pressure gauge or monitoring device.

Heavy duty cordura accessory holder pocket for harness or jacket, perfect for carrying small accessories and even a spare mask . Ideal to place on harness webbing, jacket and even on belts with webbing up to 50 mm.

High resistance cordura weight pocket for harness, with capacity for 2.3 kg ballast pads approximately. Fast closing and release clip in plastic on the outside and flap with Velcro. Ideal to place on harness webbing, tank webbing and even on belts. Stainless steel eyelet at the bottom for water drainage and rear strap to adjust to bottle buckle or harness. Sold by the unit.

The WTX and WTX-D Series is a selection of harnesses, buoyancy cells and accessories which offer unparalleled versatility due to the modular nature of the whole system. Each component can be configured into a highly technical rig for those trained to push the limits, or scaled down to make a travel friendly set up suitable for any diver.

The WTX and WTX-D Series is a selection of harnesses, buoyancy cells and accessories which offer unparalleled versatility due to the modular nature of the whole system. Each component can be configured into a highly technical rig for those trained to push the limits, or scaled down to make a travel friendly set up suitable for any diver.

Plate to fitting single tank to back plate. Stainless steel or aluminum models. It also can be used to mount twins with double tank straps (not included).
Weights: Stainless steel 0.870 kg. Aluminium 0.305 kg.

TDS Basic DIR type Harness for tech diving. 

Technical harness for back plate mounting with all necessary components included and fully adjustable. Mounting and dismounting the back plate is very versatile, as it is fixed with screws of the twin cylinders themselves

Stainless Steel Back Plate from TDS.Compatible with all DTD accessories. Holes that let adjust in two different heights. Perforations to pass the single tank straps.

Stainless Steel Back Plate from TDS.Compatible with all DTD accessories. Holes that let adjust in two different heights. Perforations to pass the single tank straps.

This simple, yet strong, harness can take the load of a fully rigged technical diver and can be easily customised with the hardware of your choice. Please note that the back plate is not included and must be purchased separately. Your back plate options for this harness are the WTX Aluminium Back Plate, the WTX Stainless Steel Back Plate and the Ultralight Travel Plate. Tank bands are also not included.

Apeks Deluxe webbed Harness with Steel Backplate for Techncial Scuba Diving: This simple yet rugged harness can hold the load of a technical diver's full equipment. It can be customized with your choice of accessories. Tank straps are not included.